Beginning Woodcarving Youtube

Beginning Woodcarving Youtube Rating: 4,2/5 3806 reviews

Wood carving is a fun, accessible, and creative craft that doesn’t require a fancy studio, or equipment. All you need is a piece of wood and something sharp to carve it with. Of course, what kind of wood and what kind of carving tools you pick will affect the difficulty, safety, and result of your wood carving endeavors. In this wood carving for beginners guide, we’ll go over some of the most important information a new craftsman or craftswoman needs to know to get started. Are you looking for information and tips for wood working? Check out this introductory wood working course for more info. Otherwise, get ready to learn the basics of wood carving, and unleash your creativity!

  1. Beginner Wood Carving Youtube
  2. Beginning Wood Carving Videos

Art Designs Studio is Lora S. Irish’s wood carving, pyrography, and crafts patterns web store with over 2500 patterns and designs, ready for you to download today. Line art, shaded drawings, and patterns for wood carving, pyrography, leather carving, applique quilting, paper crafts, scrap booking, gourd art, and so many more. Find and save ideas about Wood carving for beginners on Pinterest. See more ideas about Wood burning techniques, Wood burning tips and Pyrography ideas. Wood Carving For Beginners: Essential Tips on How to Get Started. February 5, 2014 by C. Wood carving is a fun, accessible, and creative craft that doesn’t require a fancy studio, or equipment. All you need is a piece of wood and something sharp to carve it with. Of course, what kind of wood and what kind of carving tools you pick will.

Types of Wood Carving

While it might sound like a straightforward discipline, there are actually different types of wood carving techniques. Below is four of the main wood carving styles. It’s good to determine which style best fits your abilities, and your desired product, before purchasing materials and supplies. If you’re planning on teaching a young child how to wood carve, you might want to opt for something a little safer until they’re old enough to handle sharp objects on their own. Learning how to work with clay, or carving a piece of soap with a spoon are good, safe alternatives.

Whittling One of the oldest forms of wood carving, whittling is distinct for its sharp, textured cuts that leave knife “strokes.” The sculptures made with whittling are often very angular. Whittling is done using a whittling or a carving knife.

Relief Carving Unlike carving full sculptures out of wood, relief carving is the process of carving figures into wood. You start out with a flat panel of wood, and carve figures into it, leaving the back flat.

Carving in the Round This is like the clay sculpturing of wood cutting. Objects are smooth, angles are rounded – hence the name – and all sides are carved, unlike relief carvings.

Chip Carving Chip carving involves using a knife, chisel, and a hammer. The process is exactly as the name suggests: chipping away at a piece of wood. This can be used to create intricate patterns in wooden plates and boards.

Types of Wood

Once you’ve decided on your wood carving style, it’s time to select the type of wood you want to work with. Butternut and basswood are softer types of wood that are easier for beginners to carve. Butternut offers a nice looking grain if you’re planning to leave your sculpture unpainted. Whatever you choose, make sure you purchase the wood from an art and crafts store or wood supplier. Don’t pick up any piece of wood from your lumber pile or garage, especially if you aren’t familiar with the different kinds yet. It will only end in frustration. Below is a rundown of some of the different types of wood you can carve with, based on this chart from The Sculpture Studio.

Basswood: Easy to carve, with a fine grain. Light and cream colored. Best for whittling.

Butternut: Easy to carve, with a coarse grain. Light brown colored with a distinct wood pattern.

White Pine:Easy to carve, with a medium grain. Soft and cream colored.

Mahogany: Intermediate difficulty to carve, with a medium grain. Distinct reddish color.

Black Walnut: Hard to carve, with a medium grain. Very dark brown.

Cherry: Very hard to carve, with a fine grain. Pinkish brown with a wavy pattern.

Sugar Maple: Very hard to carve, with a fine grain. Very light cream color.

White Oak: Very hard to carve, with a medium to coarse grain. Very light, yellowish color.

Types of Wood Carving Tools

You can’t carve wood without tools! Make sure you have the proper one to fit the technique you want to use.

Chip Carving Knife: The most basic wood carving tool. Chip carving knives consist of a blade that is about an inch and a half long, with a long handle designed for comfort, so it doesn’t hurt your hand. You can find chip carving knives for around $20. Good, high-quality ones sell for around $50. If you’re serious about your craft, it’s a valuable investment. A quality chip carving knife will be made of high carbon steel and will not wear out as quickly as a cheap one.

Gouges: Gouges are curved carving tools that can scoop out large or small areas of wood, depending on how wide their sweep is. U-gouges, V-gouges, and spoon gouges… there are plenty of different types that can be used for carving, shaping, and smoothing surfaces.

Chisels: Chisels are sharp tools used with mallets for wood chipping techniques. Wood chippers can a rubber mallet on their chisel, instead of a wooden one, to reduce noise and prevent too much wear and tear on their chisel’s handle.

Wood Carving Tips

Beginner

#1 – Learn how to handle a wood carving knife. Whether you’re using an x-acto knife from the garage, or you went out and purchased a fancy wood carving knife from the supply store, you need to know how to properly handle the tool before starting to dig into a piece of wood. Remember, these are sharp objects you’re working with, so you need to be careful. If you’re clumsy or unsure of yourself starting out, it’s a good idea to wear a carving glove. Wear the glove on the hand you’re holding the piece of wood with, not the hand that you’re using the knife with. Most importantly, make sure to use your wrist, and not your elbow, to control the knife. This will allow for more control over precise carvings. Also keep your knife sharp, not dull, to make carving easier.

#2 – Cut along the grain. Before you start carving, you want to determine which direction the grain of the wood is running. You can do this by carving a piece of wood out of a corner, curving out to finish the cut so the wood doesn’t rip at the end. Take note of the long, dark streaks running through the wood

#3 – Sketch out your wood cuts. Don’t rush your wood carvings. Any mistake you make is potentially permanent. You’ll have to change up your plan to integrate the mistake into the finished product, and that could sacrifice your original vision. To avoid this, it helps to lightly sketch out your cuts and carvings with a pencil. Draw out lines to cut along, and shapes to carve out. It will help you be more precise, and prevent un-fixable mistakes.

Jump-start your woodcarving with simple, traditional techniques that beginners can learn to start transforming wood into beautiful works of art. Chris Pye’s Woodcarving Course & Reference Manual (Fox Chapel Publishing, 2012) is a guide to getting started. In the following excerpt, Pye gives instructions for seven cuts that form the basis of the woodworking craft.

You can purchase this book from the MOTHER EARTH NEWS store: Chris Pye’s Woodcarving Course & Reference Manual: A Beginner’s Guide to Traditional Techniques.

In your hand is a sharp and well-shaped carving tool. You hold it in a safe grip that will let you carve with confidence and facility. Now you want to make things happen — but how exactly? What can you make these tools do? Well, a lot more than most newcomers think!

Here’s a learning-the-guitar analogy: After you have understood tuning (sharpening) and how to hold the guitar (grips), I imagine our guitar teacher would probably have you plucking strings. You would just play around lightly in a relaxed way, getting a sense of how the guitar works and the notes and chords you could make. So, before turning to woodcarving projects — our tunes proper, so to speak — I want to look at what we can call the outcome of the tool, the sort of notes you can play with a gouge.



Gouge Tools Needed

• Your gouges and V-tools. Do try what I suggest with different tools.

• A board of clean carveable wood held safely to the bench. I always like to start with a planed surface. A full cut is just one of the basic carving techniques you can do.

Cuts of the Carver

Visit the Image Gallery for a photo of each woodcarving cut.

As a sample of the versatility of traditional carving tools, I’m going start by separating out a few of the cuts carvers make. Of course, you won’t be thinking in separate cuts like this when you are deep into your carving; you’ll just be working with the tool and eventually forgetting about it.

1. Running Cut

How to do it: This is similar to the low-angle grip. One hand at the rear propels the tool and the other, wrapped around the blade, resists. The blade hand rests on the wood for control as you start, stop, and direct the cut at will, swapping hands to reverse direction. The nature of a running cut is that it keeps going; it’s a long stroke.

Try running parallel and equal lines of varying depths with your V-tool; then cut curves to the right and left, swapping hands, and so on. Tilt the V to the left and right and observe. Try with a narrow, deep gouge or U tool.

With a deep gouge (#8 or #9) run a long channel across the grain. A single deep channel like this is called a flute.

Place a second channel as similar as possible to the side, then a third, and so on. The surface will look a bit like it’s been plowed.

Application: Running cuts with V- and U-tools have obvious drawing-like applications for veins and hair etc. Lowering the background in this way is a much more efficient approach than simply carving away wood here and there at random.

2. Stabbing Cut

How to do it: Using the high-level grip, put the weight of your shoulder behind the handle. Push the cutting edge of the carving tool straight into the wood and pull it out again.


Woodcarving
Wood

Try the cut with a medium gouge: straight in and out. If you wobble the handle from side to side you are likely to break off a corner. To release a stuck blade from the wood, ease it out by tilting the handle in a direction along the edge.

Make some surface patterns with a gouge.

Try emphasizing just one corner as you push in. You’ll make a stab cut that starts deep at one end and fades around the curve (sweep) into nothing. You thus have two cuts: to the left and right.

Application: Stab cuts are used decoratively, say in the details of hair and fur, and to give emphasis by adding a harder shadow, such as between lips or at the end of a running line. Use your mallet to stab into particularly hard wood.

With a change in function, the stab cut can become the very important stop cut.

3. Stop Cut

How to do it: When you place a stab cut so as to control the wood grain — to stop them from breaking out — you have a stop cut. You would make a simple stop cut in exactly the same way as the stabbing cut.

You can see the stop cut in action clearly in a medieval decorative element called a thumbnail (or fingernail): Make a strong vertical stab cut with a deep gouge and mallet at one end of the fingernail — this is the stop cut. Scoop up to this with the same gouge. It’s easiest to work across the grain and you may have to cut the thumbnail itself with a few passes. Try making the scoop cut first. You’ll see the bevel of the tool wedges the wood fibers up and forward and finding a precise place to end the cut is difficult. Thus we place the stop cut first to control this wedging effect.

Repeating these thumbnails side by side will create a simple molding. A challenge would be to make a dozen even and equal ones, side by side.

Application: By its very nature, the stop cut has a job to do, and, having done it, the stop cut disappears; it is subsumed by the cuts that follow. This is what separates the stop cut from the stab cut; the stab cut remains on the surface to make its own effect.

You can also see stop cuts in traditional incised lettering: a heavy stop cut goes in first in the center of part of a letter, controlling the grain; subsequent angle cuts come in from either side to leave the V trench.

We also made stop-type cuts in the last chapter when we finished off the delta-shaped V cuts with a skew chisel. We could have put in the stop cuts first. And a running cut or groove can act as a sort of fire break —functionally a stop cut — to prevent grain splintering.

Woodcarvers will use stop cuts when necessary and without thinking. Don’t hesitate to apply one to your carving when you need to control the grain.

4. Sweep or Rocking Cut

(Note: Remember that the sweep of a gouge is its profile seen end on. In a true gouge, the sweep is a part, an arc, of a circle — unlike U-shaped gouges.)

How to do it: The sweep of a gouge is an arc of a circle. Rotate the handle as you push your gouge forward in a short, scooping, running cut. You will be able to feel the edge slicing across the wood as it follows its arc.

You can make a sweep cut with either low or high-angle grip, rotating to the left or the right. Make some sweep cuts with a medium gouge (about #6).

Besides other best and cheap internet security software available Kaspersky is the best choice among them. On the final note, it is good internet security software for protecting your PC against viruses and web related threats. Cnet best internet security. Kaspersky is also available for 1 2 and 3 PC user license. Featured on Cnet, Softonic, Filehippo, majorgeeks, etc.

Start and end the sweep cut with the corners clear to avoid tearing the grain. The scooping action of the cut has three parts: the tool enters the wood; you then drop the handle a little and move the edge along as you rotate; you then drop the handle further as you make the exit.

More than anything, this is a feely cut and is done with both hands working together: feel the sweep as you scoop.

Try it with deep gouges too, and rotate the handle both clockwise and counterclockwise.

Rotate the tool along the arc of the sweep but do not wiggle or rock the handle from side to side: this will tear the grain, tend to blunt the cutting edge, and may even result in chipping the metal or losing a corner.

Application: The slicing action eases the tool through the wood and produces a much cleaner cut. The movement is also called a rocking cut, sometimes called “rocking the tool through its cut.” Slicing the tool like this along the edge — in this case making full use of the sweep — is, more than any other, the cut of the carver. Indeed I’d say that if you take out running and stop cuts, all my cuts are sliced in some way.

One form of the sweep cut is the all-important slicing cut that you make with the flattest gouges.

Beginner Wood Carving Youtube

5. Slicing Cut

Beginning Wood Carving Videos

How to do it: The arc of the circle that forms the sweep of a very flat (#3) gouge is so big that it’s impossible to rotate the gouge meaningfully at the handle: the corners dig in immediately.

So, you have to emphasize the sideways movement as the tool moves forward. Think of paring the surface, drifting the edge across, rather than actually rotating the tool; in fact you are hardly rotating at all.

With a #3 gouge in the low-level grip, make very shallow slicing cuts, keeping the corners clear at all times. Work at right angles to the grain — in other words across it — and you’ll find the slice itself will be more or less along the grain.

Slice from left to right and from right to left. Keep the area clean as you go along. It’s tricky at first not to dig the corners in. If you do, immediately go over the torn grain and repair the surface.

Application: This is the cut for flattening and finishing off a surface, from backgrounds to bodies, wherever you choose to finish from the tools rather than sanding. The proviso here is that the closer you can match the sweep to the form, the smoother a surface you will leave; and sometimes, of course, the sweep you need to match the form will not be the flattest.

The same slicing action is also used in cutting the curves of incised letters.

So there, in brief, are some basic cuts. You’ll need them again and again in projects.

Learn more: Read Pye's guide to the gouge tool, which can be used to create verstile cuts, even by beginners.

This excerpt has been reprinted with permission from Chris Pye’s Woodcarving Course & Reference Manual: A Beginner’s Guide to Traditional Techniques, published by Fox Chapel Publishing, 2012. Buy this book from our store: Woodcarving Course & Reference Manual.

Comments are closed.